Deployment of Unmanned Aerial Vehicle during surface CO2 release experiments at the Ginninderra greenhouse gas controlled release facility H. Berko (CO2CRC, Geoscience Australia), F. Poppa (The Australian National University), U. Zimmer (The Australian National University) and A. Feitz (CO2CRC, Geoscience Australia) Lagrangian stochastic (LS) forward modelling of CO2 plumes from above-surface release experiments conducted at the GA-CO2CRC Ginninderra controlled release facility demonstrated that small surface leaks are likely to disperse rapidly and unlikely to be detected at heights greater 4 m; this was verified using a rotorcraft to map out the plume. The CO2 sensing rotorcraft unmanned aerial vehicle (RUAV) developed at the Australian National University, Canberra, is equipped with a CO2 sensor, a GPS, lidar and a communication module. It was developed to detect and locate CO2 gas leaks; and estimate CO2 concentration at the emission source. The choice of a rotor-craft UAV allows slower flight speeds compared to speeds of a fixed-wing UAV; and the electric powered motor enables flight times of 12 min. In experiments conducted at the Ginninderra controlled release facility, gaseous CO2 (100 kg per day) was released from a small diffuse source located in the middle of the paddock, and the RUAV was flown repeatedly over the CO2 source at a few meters height. Meteorological parameters measured continuously at the site at the time of the flight were input in the LS model. Mapped out horizontal and vertical CO2 concentrations established the need to be close to the ground in order to detect CO2 leakage using aerial techniques. Using the rotorcraft as a mobile sensor could be an expedient mechanism to detect plumes over large areas, and would be important for early detection of CO2 leaks arising from CCS activities.

A short animation of an atmospheric simulation of methane emissions from a coal mine (produced using TAPM) compared to actual methane concentrations detected by the Atmospheric Monitoring Station, Arcturus in Central Queensland. It illustrates the effectiveness of both the detection and simulation techniques in the monitoring of atmospheric methane emissions. The animation shows a moving trace of both the simulated and actual recorded emissions data, along with windspeed and direction indicators. Some data provided by CSIRO Marine and Atmospheric Research.

Abstract for a Poster for the CO2CRC Symposium 2013: Atmospheric tomography is a CO2 quantification and localisation technique that uses an array of sampling points and a Bayesian inversion method to solve for the location and magnitude of a CO2 leak. Knowledge of a normalized three-dimensional dispersion plume is required in order to accurately model a leak using many meteorological parameters. A previous small scale (~20 m) study using a high precision Fourier Transform Infrared found that the emission rate was determined to within 3% of the actual release rate and the localisation within 1 m of the correct position. The technique was applied during the CO2CRC Otway Stage 2B residual saturation and dissolution test in August-October 2011. A network of eight independent CO2 sensors (Vaisala GMP343 CO2 probes) were positioned at distances ranging from 154 to 473 m from the well. A 3D sonic anemometer within the measurement area collected wind turbulence data. The results of the study indicate that, through careful data processing, measurements from the reasonably inexpensive (but lower accuracy and lower precision) CO2 sensor array can provide useful data for the application of atmospheric tomography. Results have found that the low precision of the sensors over time becomes a problem due to sensor drift. A reference measurement of CO2 helps to resolve this problem and improves the perturbation signal during data processing. Preliminary inversion modeling results will be shown to show the best estimation of locating a CO2 leakage source for the Otway Stage 2B residual saturation and dissolution test. CO2CRC Symposium 2013, Hobart

Having techniques available for the accurate quantification of potential CO2 surface leaks from geological storage sites is critical for regulators, public assurance and for underpinning carbon pricing mechanisms. Currently, there are few options available that enable accurate CO2 quantification of potential leaks at the soil-atmosphere interface. Integrated soil flux measurements can be used to quantify CO2 emission rates from the soil and atmospheric techniques such as eddy covariance or Lagrangian stochastic modelling have been used with some success to quantify CO2 emissions into the atmosphere from simulated surface leaks. The error for all of these techniques for determining the emission rate is not less than 10%. A new technique to quantify CO2 emissions was trialled at the CO2CRC Ginninderra controlled release site in Canberra. The technique, termed atmospheric tomography, used an array of sampling sites and a Bayesian inversion technique to simultaneously solve for the location and magnitude of a simulated CO2 leak. The technique requires knowledge of concentration enhancement downwind of the source and the normalized, three-dimensional distribution (shape) of concentration in the dispersion plume. Continuous measurements of turbulent wind and temperature statistics were used to model the dispersion plume.

Australia had a long and illustrious association with 'space science'. The first Australians used the patterns of the stars to guide them to seasonal food sources. Captain Cook arrived here on the way home from a voyage to chart the transit of Venus, with the goal of improving navigational technology. When Governor Phillip founded the first European settlement, he brought with him the astronomer William Dawes. Australia was the fourth nation to build and launch a satellite from its own territory. The 'big dish' at Parkes played an important role in the Apollo missions and the discovery of the first quasar.

11-5413 The Probabilistic Volcanic Ash - Hazard Map movie describes how you construct a probabilistic hazard map for volcanic ash, using an example scenario from GA's volcanic ash modelling work in West Java, Indonesia. The target audience is other govt. agencies both national and international, and the general public. The 3.3 minute movie uses 3D Max animations and 2D affects, has narration and production music. The narration will also be done in Bahasa Indonesian, at a later date.

Unlocking the Landsat Archive (ULA) project poster presentation outlining the background to the project, it's objectives and major components.

Geoscience Australia and CO2CRC have constructed a greenhouse gas controlled release reference facility to simulate surface emissions of CO2 (and other GHG gases) from an underground slotted horizontal well into the atmosphere under controlled conditions. The facility is located at an experimental agricultural station maintained by CSIRO Plant Industry at Ginninderra, Canberra. The design of the facility is modelled on the ZERT controlled release facility in Montana. The facility is equipped with a 2.5 tonne liquid CO2 storage vessel, vaporiser and mass flow controller unit with a capacity for 6 individual metered CO2 gas streams (up to 600 kg/d capacity). Injection of CO2 into soil is via a shallow (2m depth) underground 120m horizontally drilled slotted HDPE pipe. This is equipped with a packer system to partition the well into six CO2 injection chambers. The site is characterised by the presence of deep red and yellow podsolic soils with the subsoil containing mainly kaolinite and subdominant illite. Injection is above the water table. The choice of well orientation based upon the effects of various factors such as topography, wind direction, soil properties and ground water depth will be discussed. An above ground release experiment was conducted from July - October 2010 leading to the development of an atmospheric tomography technique for quantifying and locating CO2 emissions1. This technique will be applied to the first sub-surface experiment held in January-March 2012 in addition to soil flux surveys, microbiological surveys, and tracer studies. An overview of monitoring experiments conducted during the subsurface release and preliminary results will be presented. Additional CO2 releases are planned for late 2012 and 2013. Abstract for "11th Annual Conference on Carbon Capture Utilization & Sequestration" April 30 - May 3, 2012, Pittsburgh, Pennsylvania

An atmospheric greenhouse gas (GHG) monitoring station began operation in July 2010 near Emerald, Queensland. The station is part of a collaborative project between Geoscience Australia (GA) and CSIRO Marine and Atmospheric Research (CMAR) to establish and operate a high precision atmospheric monitoring facility for measurement of baseline greenhouse gases (GHG) in a high priority geological carbon dioxide storage region. The primary purpose of the station is to field test newly developed greenhouse gas monitoring technology and demonstrate best practice for regional baseline atmospheric monitoring appropriate for geological storage of carbon dioxide. The GHG records were to be used as a reference for monitoring of the atmosphere at a CO2 storage project, providing a baseline to quantify typical variations in the area and a background against which any anomalies in the immediate vicinity of the storage might be detected. The site chosen for the GHG atmospheric monitoring station is in the locality of Arcturus, 50 km southeast of Emerald in the Central Highlands, Queensland. Site selection was based on the recommendations of the Carbon Storage Taskforce's National Carbon Mapping and Infrastructure Plan, regional assessments of prospective basins, regional atmospheric modelling, and consultation with key stakeholders. The key driver for the stakeholder consultation group was to support early projects for large scale onshore geological storage. Both the Bowen and Surat basins were identified as potential early mover onshore storage regions by the group and suitable for a regional atmospheric monitoring station. During early 2010, ZeroGen had an active exploration program for geological storage and the site was eventually located approximately 8km upwind from the boundary of ZeroGen's most prospective storage area in the northern Denison Trough, part of the larger Bowen Basin. The Arcturus site and environs is representative of the activities and ecology of Queenslan's Central Highlands and the greenhouse gas signals are likely be influenced by cropping, pasture, cattle production, and gas and coal activities. These same activities are also likely to be dominant sources of greenhouse gases in the Surat Basin. Importantly, the site is secure, can be accessed via an existing road, is not subject to flooding, and has easy access to electrical lines that only required the installation of a transformer on an electric pole. A long lead time for new electricity connections at remote sites (potentially greater than 12 months) was identified as a key risk to the project. Negotiations with the electricity supplier resulted in connection in less than 4 months. An access agreement was negotiated with the landowner to enable the installation of the monitoring station and access to the site.

Nadir BRDF Adjusted Reflectance correction standardizes Landsat data to enable image intercomparison. The method accounts for within-scene sun, view and sensor geometry variations by using coupled physics-based atmospheric and BRDF models. The BRDF shape functions derived from the Moderate Resolution Imaging Spectroradiometer (MODIS) data with the MODerate resolution atmospheric TRANsmission version 5 (MODTRAN) radiative transfer model.