Moreton Bay 2009 LiDAR data was captured over the Moreton Bay Regional Council area between March and June 2009. The data was acquired by AAM Hatch (now AAMGroup) and funded by Queensland and Commonwealth governments. The project area covering 2440sqkm is licenced for use by all Commonwealth, State and Local Government organisations. Data acquisition and post-processing has been controlled to achieve a vertical accuracy witihn 0.15m (RMS, 68% CI) and horizontal accuracy within 0.45 m. Horizontal coordinates are based upon Map Grid of Australia (MGA) Zone 56 projection. Vertical coordinates are referenced to Australian Height Datum (AHD). The data was captured with point density of 2.5 points per square metre and the data is available as mass point files (ASCII, LAS) and ESRI GRID files with 1m grid spacing in 1km tiles.

These datasets cover approximately 27 sq km over all of Mabuiag Island within the Torres Strait Island Regional Council and are part of the 2010 Torres Strait Islands LiDAR capture project. This project, undertaken by Vekta Pty Ltd on behalf of the Queensland Government captured highly accurate elevation data using LiDAR technology. Available dataset formats (in 1 kilometre tiles) are: - Classified las (LiDAR Data Exchange Format where strikes are classified as ground, vegetation or building) - 1 metre Digital Elevation Model (DEM) in ASCII xyz - 1 metre Digital Elevation Model (DEM) in ASCII grid - 1 metre Digital Elevation Model (DEM) in ESRI grid - 0.25 metre contours in ESRI Shape

AAMHatch acquired Airborne Laser Scanning (ALS) data for the Sydney Metropolitan area between 11 June 2007 & 7 July 2007 and again in February to June 2008. The source data are available as mass points (ASCII XYZ, LAS) and Gridded 2m and 10m DEM tiles or 2m Mosaic. The vertical accuracy is 0.15m at 1 sigma in open clear ground as specified in the project scope. All data are referenced to GDA94/MGA Zone 56 and AHD using independent survey control which means the project area is not seamless and height difference between the 2007 and 2008 data will exist. A hydrologically enforced elevation model is available for this product, which should be used for any water modelling.

This project consists of data that has been reprocessed by RPS and AAM for the purpose of creating an improved Victorian coastal DEM including contours based on the original data acquired in 2007. The purpose of this project is to reclassify the original level 2 classification LiDAR data into level 3 for input to a higher accuracy ICSM Level 3 classification (Level 3 DEM). LiDAR (Light Detection and Ranging) is an airborne remote sensing technique for rapid collection of terrain data. The sensor used for this LiDAR project collected XYZ and Intensity data for first and last return by bouncing a pulse from the aircraft to the surface that enables the height and intensity values to be calculated. From the raw LiDAR data, a suite of elevation products was generated including DEM and Contours. Project Products: DEM, Contours, raw LiDAR.

The data covers an area of approximately 4000 sq km in the Namoi Valley, located around Narrabri, NSW. The LiDAR was captured by RPS Spatial in September and October 2013 with a point density of two points per square metre. The specified accuracies; 30cm vertical and 80cm horizontal, were achieved and verified through a rigorous network of check points and base stations. A set of seamless products were produced including hydro-flattened bare earth DEMs, DSMs, Canopy Height Models (CHM) and Foliage Cover Models (FCM). The outputs of the project are compliant with National ICSM LiDAR Product Specifications and the NEDF.

These datasets cover approximately 5700 sq km in the eastern sector of the Fraser Coast Regional Council and all of Fraser Island and are part of the 2009 Fraser Coast LiDAR capture project. This project, undertaken by Vekta Pty Ltd on behalf of the Queensland Government captured highly accurate elevation data using LiDAR technology. Available dataset formats (in 1 kilometre tiles) are: - Classified las (LiDAR Data Exchange Format where strikes are classified as ground or non-ground) - 1 metre Digital Elevation Model (DEM) in ASCII xyz - 1 metre Digital Elevation Model (DEM) in ESRI ASCII grid - 0.25 metre contours in ESRI Shape

The Brisbane hydrologically enforced digital elevation model (DEM) was created from a combination of the following surveys; Brisbane 2009 LiDAR, Redland 2009 LiDAR, Gold Coast 2009 LiDAR, Moreton Bay 2009 LiDAR and Logan 2009 LiDAR survey areas. The data is licensed for use by all Commonwealth, State and Local Government. Data acquisition and post-processing for all of the input surveys has been controlled to achieve a fundamental vertical accuracy of <0.15m (RMS, 68% CI) and horizontal accuracy within 0.45 m. Horizontal coordinates are based upon Map Grid of Australia (MGA) Zone 56 projection. Vertical coordinates are referenced to Australian Height Datum (AHD). The hydrologically conditioned and drainage enforced 2m DEM or HDEM was developed in 2010 as part of the Urban DEM project managed by the CRC for Spatial Information and Geoscience Australia. The HDEM was produced by SKM using the ANUDEM program. The HDEM ensures that primary stream/channel flow, and water flow across the land surface are accurately represented. The hydrologically enforced elevation model should be used for hydrological modelling.

These datasets cover approximately 400 sq km in the central, northern and eastern sectors of the Townsville City Council and are part of the 2009 Tropical Coast LiDAR capture project. This project, undertaken by Fugro Spatial Solutions Pty Ltd on behalf of the Queensland Government captured highly accurate elevation data using LiDAR technology. Available dataset formats (in 2 kilometre tiles) are: - Classified las (LiDAR Data Exchange Format where strikes are classified as ground, non-ground or building) - 1 metre Digital Elevation Model (DEM) in ASCII xyz - 1 metre Digital Elevation Model (DEM) in ESRI ASCII grid - 0.25 metre contours in ESRI Shape

These datasets cover approximately 1400 sq km along the eastern sector of the Cassowary Coast Regional Council and are part of the 2009 North Queensland LiDAR capture project. This project, undertaken by Photomapping Services on behalf of the Queensland Government captured highly accurate elevation data using LiDAR technology. Available dataset formats (in 1 kilometre tiles) are: - Classified las (LiDAR Data Exchange Format where strikes are classified as ground, vegetation or building) - 1 metre Digital Elevation Model (DEM) in ESRI grid - 1 metre Digital Elevation Model (DEM) in ASCII xyz - 1 metre Digital Elevation Model (DEM) in shapefile - 0.25 metre contours in ESRI Shape

This project consists of data that has been reprocessed by RPS and AAM for the purpose of creating an improved Victorian coastal DEM including contours based on the original data acquired in 2007. The purpose of this project is to reclassify the original level 2 classification LiDAR data into level 3 for input to a higher accuracy ICSM Level 3 classification (Level 3 DEM). LiDAR (Light Detection and Ranging) is an airborne remote sensing technique for rapid collection of terrain data. The sensor used for this LiDAR project collected XYZ and Intensity data for first and last return by bouncing a pulse from the aircraft to the surface that enables the height and intensity values to be calculated. From the raw LiDAR data, a suite of elevation products was generated including DEM and Contours. Project Products: DEM, Contours, raw LiDAR.