This map is part of a series which comprises 50 maps which covers the whole of Australia at a scale of 1:1 000 000 (1cm on a map represents 10km on the ground). Each standard map covers an area of 6 degrees longitude by 4 degrees latitude or about 590 kilometres east to west and about 440 kilometres from north to south. These maps depict natural and constructed features including transport infrastructure (roads, railway airports), hydrography, contours, hypsometric and bathymetric layers, localities and some administrative boundaries, making this a useful general reference map.

At this scale 1cm on the map represents 1km on the ground. Each map covers a minimum area of 0.5 degrees longitude by 0.5 degrees latitude or about 54 kilometres by 54 kilometres. The contour interval is 20 metres.

Redland 2009 LiDAR survey was captured over the Redland City Council region between 25th March and 9th June 2009. The data was acquired by AAM Hatch (now AAMGroup) and funded by Queensland and Commonwealth governments. The data is licensed for use by all Commonwealth, State and Local Government. Data acquisition and post-processing has been controlled to achieve a vertical accuracy within 0.15m (RMS, 68% CI) and horizontal accuracy within 0.45 m. Horizontal coordinates are based upon Map Grid of Australia (MGA) Zone 56 projection. Vertical coordinates are referenced to Australian Height Datum (AHD). The data was captured with point density of 2.5 points per square metre and the data is available as mass point files (ASCII, LAS) and ESRI GRID files with 1m grid spacing in 1km tiles. The data are available as a number of surface types, products and formats including: mass points, digital elevation model (DEM) and hydrologically enforced DEM (HDEM) for the low lying coastal areas. Redland DEM forms part of the Brisbane HDEM which is a combination of the Brisbane 2009 LiDAR, Redland 2009 LiDAR, Moreton Bay 2009 LiDAR and Logan 2009 LiDAR survey areas.

This series covers the whole of Australia at a scale of 1:250 000 (1cm on a map represents 2.5 km on the ground) and comprises 513 maps. This is the largest scale at which published topographic maps cover the entire continent. Each standard map covers an area of 1.5 degrees longitude by 1 degree latitude or about 150 kilometres from east to west and 110 kilometres from north to south. There are about 50 special maps in the series and these maps cover a non-standard area. Typically, where a map produced on standard sheet lines is largely ocean it is combined with its landward neighbour. These maps contain natural and constructed features including road and rail infrastructure, vegetation, hydrography, contours (interval 50m), localities and some administrative boundaries. Some maps are supplemented by relief shading. The topographic map and data index shows coverage of the sheets. Product Specifications Coverage: The series covers the whole of Australia with 513 maps. Currency: Ranges from 1995 to 2009. Coordinates: Geographical and either AMG or MGA (post-1993) Datum: AGD66, GDA94, AHD. Projection: Universal Traverse Mercator (UTM) Medium: Paper, flat and folded copies. Forward Program: Selected maps under revision.

AAMHatch acquired Airborne Laser Scanning (ALS) data for the Sydney Metropolitan area between 11 June 2007 & 7 July 2007 and again in February to June 2008. The source data are available as mass points (ASCII XYZ, LAS) and Gridded 2m and 10m DEM tiles or 2m Mosaic. The vertical accuracy is 0.15m at 1 sigma in open clear ground as specified in the project scope. All data are referenced to GDA94/MGA Zone 56 and AHD using independent survey control which means the project area is not seamless and height difference between the 2007 and 2008 data will exist. A hydrologically enforced elevation model is available for this product, which should be used for any water modelling.

These datasets cover approximately 1400 sq km in the northern sector of the Lockyer Valley Regional Council and comprise the 2010 Lockyer Valley LiDAR capture project. This project, undertaken by AAM Pty Ltd on behalf of the Queensland Government captured highly accurate elevation data using LiDAR technology. Available dataset formats (in 1 kilometre tiles) are: - Classified las (LiDAR Data Exchange Format where strikes are classified as ground, non-ground or building) - 1 metre Digital Elevation Model (DEM) in ASCII xyz - 1 metre Digital Elevation Model (DEM) in ESRI ASCII grid - 0.25 metre contours in ESRI Shape

<p><b>Please note: </b>This topographic map is not available from Geoscience Australia.<p>For availability, refer to NSW Government mapping agency.

At this scale 1cm on the map represents 1km on the ground. Each map covers a minimum area of 0.5 degrees longitude by 0.5 degrees latitude or about 54 kilometres by 54 kilometres. The contour interval is 20 metres.

<p><b>Please note: </b>This topographic map is not available from Geoscience Australia.<p>For availability, refer to NSW Government mapping agency.

At this scale 1cm on the map represents 1km on the ground. Each map covers a minimum area of 0.5 degrees longitude by 0.5 degrees latitude or about 54 kilometres by 54 kilometres. The contour interval is 20 metres.