These documents have been scanned by the GA Library. Please refer to the document for contents.

These documents have been scanned by the GA Library. Please refer to the document for contents.

These documents have been scanned by the GA Library. Please refer to the document for contents.

These documents have been scanned by the GA Library. Please refer to the document for contents.

Between April and July 1962, a seismic party from the Bureau of Mineral Resources, Geology and Geophysics made a seismic reflection and refraction survey in the Moree area of New South Wales. The main purpose of the survey was to investigate whether the southern extension of the Bowen Basin beneath the Great Artesian Basin from Meandarra to Toobeah continued as far south as Moree and joined the Sydney Basin. Three east-west traverses were shot using a method of reconnaissance reflection shooting, the first near Dolgelly Bore, the second through Moree, and the third through Bellata. The third traverse was extended eastward as far as the Horton River to investigate the Hunter-Bowen Thrust zone. In addition, three north-south refraction traverses were shot in the middle, and on both ends, of the east-west traverse through Moree. A north-south reflection traverse was shot north of Dolgelly Bore.Results in the Moree and Bellata areas were of poor quality and in the Bellata area in particular, owing to surface basalt flows, little information was obtained. The Hunter-Bowen Thrust area was not distinguished by the seismic work. The seismic results indicated that the trough of sediments extending southwards through Dolgelly Bore was at least 7500 ft deep south of Dolgelly Bore. The eastern margin of the trough is probably an overthrust fault. In the Moree area, two troughs were indicated, viz. the Biniguy Trough in the east where about 7000 ft of sediments was estimated separated by the Pallamallawa Ridge from the Moree Trough in the west where about 11,000 ft of sediments was estimated. Poor results in the Bellata area failed to indicate whether the Moree Trough joined the Sydney Basin.

A seismic velocity survey of the APM Development Pty Limited No. 1 bore at Rosedale, Victoria, was made by the Geophysical Branch of the Bureau on the 3rd May 1960 using a TIC three-component well geophone. Measurements were taken with the geophone suspended in the well at selected intervals down to 5500 ft. It was apparent that signals reached the geophone by transmission along the cable by which it was suspended, and these interfered with the signals reaching the geophone along a path directly through the ground. This made interpretation difficult; however, by careful inspection of both the vertical and horizontal components of the signals received by the geophone at each depth, an interpretation has been made that yields a series of velocity/depth determinations. The average vertical velocity increases from 5000 ft/sec at the surface to 8930 ft/sec at a depth of 5500 ft. The average velocity in the Tertiary (0-2159 ft below datum) was computed to be 6420 ft/sec; the -werage velocity in the Mesozoic rocks penetrated (2159-5314 ft below datum) was 12,180 ft/sec. Two reflection spreads laid out and recorded in the vicinity of the bore showed the presence of reflectors at depths estimated to be in excess of 7700ft.

The R502 series of maps has been replaced by the National Topographic Map Series (NTMS). The R502 series consists of 542 map sheets and covers Australia at a scale of 1:250,000. It was compiled from aerial photography, but only about one quarter of the series was contoured. The standard sheet size is 1 degree of latitude by 1.5 degrees of longitude. Transverse Mercator map projection and Clark 1858 datum were used. Coverage of the country was completed in 1968.

The R502 series of maps has been replaced by the National Topographic Map Series (NTMS). The R502 series consists of 542 map sheets and covers Australia at a scale of 1:250,000. It was compiled from aerial photography, but only about one quarter of the series was contoured. The standard sheet size is 1 degree of latitude by 1.5 degrees of longitude. Transverse Mercator map projection and Clark 1858 datum were used. Coverage of the country was completed in 1968.

The R502 series of maps has been replaced by the National Topographic Map Series (NTMS). The R502 series consists of 542 map sheets and covers Australia at a scale of 1:250,000. It was compiled from aerial photography, but only about one quarter of the series was contoured. The standard sheet size is 1 degree of latitude by 1.5 degrees of longitude. Transverse Mercator map projection and Clark 1858 datum were used. Coverage of the country was completed in 1968.

Legacy product - no abstract available