USING MULTIBEAM ACOUSTIC REMOTELY SENSED DATA TO INVESTIGATE THE SEDIMENT GRAIN SIZE CHARACTERISTICS  

Authors / CoAuthors

Huang, Z. | Siwabessy, J. | Nichol, S.

Abstract

Acoustic remote sensing is the only effective technique to investigate deep sea bottom. Modern high-frequency multibeam echosounders transmit and receive backscatter signals from hundreds of narrow-angle beams which enlighten small footprints on the seabed. They can produce bathymetry and backscatter data with a spatial resolution around 2% of water depth, which enables us to map the seabed with great detail and accuracy. After calibration, the backscatter intensity is largely controlled by three seabed physical properties: the acoustic impedance contrast (often called hardness), apparent interface roughness (relative to acoustic frequency) and volume inhomogeneity [3, 4, 7]. These seabed physical properties are directly related to sediment grain size characteristics at the sedimentary areas. Studies showed that backscatter intensity had a moderate and positive correlation with sediment mean grain size [1, 3, 6]. Also, backscatter intensity was found to be positively correlated with coarse fractions and inversely correlated with finer fractions [2, 5, 6]. Other sediment grain size properties, especially sorting may also play important roles in the backscatter-sediment relationship [3, 5, 6]. The backscatter-sediment relationship, however, is complex in nature. Research is needed to better understand how acoustic sound interacts with sediment. This study aims to explore this relationship using a set of high quality sediment and multibeam backscatter data, and a robust spatial modelling technique. The co-located sediment and multibeam data were collected from four different areas of Australian margin which represent different sedimentary environments. Five hundred sixty-four sediment grab samples were taken from these survey areas. They were analysed in laboratory using the same procedure to generate grain size properties of %gravel, %sand, %mud, mean grain size, sorting, skewness and kurtosis. The multibeam data were collected using Kongsberg's 300 kHz EM3002 system. The raw multibeam backscatter was processed using the CMST-GA MB Process v8.11.02.1 software developed by Geoscience Australia and the Centre for Marine Science and Technology at Curtin University of Technology. As a result, the backscatter mosaics from incidence angles of 1o to 60o, at an interval of 1o, were generated. The backscatter intensity values from these 60 incidence angles were extracted for all of the sediment samples. The machine learning model Random Forest Decision Tree (RFDT) was used to investigate the backscatter-sediment relationship. The seven sediment grain size properties were the explanatory variables. The response variable was the backscatter intensity from each incidence angle. The model performance was evaluated using 10-fold cross-validation. For incidence angles between 1o and 42o, the RFDT models achieved fairly good performance, with a percentage of variance explained around 70% (Figure 1). The model performance gradually decreased for the outer beam range (incidence angle > 42o). Mud content was consistently identified as the most important explanatory variable to the backscatter strength. The second most important explanatory was usually sediment mean grain size. The RFDT models were also able to generate predicted response curves to quantitatively investigate the relationships between the important explanatory variables and individual response variables. The predicted relationship between %mud and the acoustic backscatter intensity is shown in Figure 2. This indicates a negative but non-linear relationship, with the increase of mud content in the sediment, the backscatter intensity decreases. This finding is consistent with that of previous studies [2, 5, 6]. Fine sediment with high mud content not only is soft (e.g., low impedence contrast) but also has high acoustic penetration (e.g., high attenudation in sediment), which naturally incurs low backcatter return

Product Type

nonGeographicDataset

eCat Id

89851

Contact for the resource

Keywords

• External PublicationAbstract

( Theme )

• backscatter

Australian and New Zealand Standard Research Classification (ANZSRC)

• Marine Geoscience

• Published_Internal

Publication Date

2015-01-01T00:00:00

Creation Date

Security Constraints

Australian Government Security ClassificationSystem    

Classification - unclassified

Legal Constraints

Creative Commons Attribution 4.0 International Licence    

Access - restricted

Use - license

Status

Purpose

Maintenance Information

notPlanned

Topic Category

oceans

Series Information

Lineage

This study used GA's multibeam and sediment data collected at four areas.

Parent Information

Extents

Reference System

Spatial Resolution

Service Information

Associations

Downloads and Links

Source Information

Source data not available.