Carbon capture and storage is a mitigation strategy that could rapidly reduce CO2 emissions from high emission sources. However, the exploration and assessment of reservoirs for the geological storage of CO2 is a complicated science commonly hampered by large uncertainties. The major hurdles lie in correctly assessing the prospectivity of basin plays, and ultimately of play fairways suitable for CO2 storage. On the North West Shelf of Australia, turbidite deposits are a common depositional system and many are considered prospective for CO2 storage in this emission intensive part of Australia. Using an integrated reservoir modelling approach, this study assessed the storage potential of the Caswell Fan turbidite in the Browse Basin, Western Australia. A detailed seismic interpretation utilising both 2D and 3D seismic and four previously drilled wells, provided the sequence stratigraphic framework for a detailed reservoir evaluation. The Fan was deposited in a basin floor fan setting within a lowstand systems tract, which provided optimal conditions for sequestration due to the sandstone's extended geometry, sorting, and high net-to-gross ratios, all overlain by a regional marine claystone seal. Through 3D static geological modelling it was determined that the Caswell Fan had an estimated storage capacity of approximately 300 million tonnes of CO2. This largely unconfined basin floor fan represents one of several plays along the North West Shelf of Australia, which could provide suitable CO2 storage formations for the carbon capture and storage industry.

A major concern for regulators and the public with geologically storage of gas is the potential for the migration of gas (e.g. CO2) via a leaky fault or well into potable groundwater supplies. Given sufficient CO2, an immediate effect on groundwater would be a decrease in pH which could lead to accelerated weathering, an increase in alkalinity and the release of major and minor ions. Laboratory and core studies have demonstrated that on contact with CO2 heavy metals can be released under low pH and high CO2 conditions (particularly Pd, Ni and Cr). There is also a concern that trace organic contaminants could be mobilised due to the high solubility of many organics in supercritical CO2. These scenarios could potentially occur under a high CO2 leakage event but a small leak might be barely perceptible yet could provide an important early warning for a subsequent and more substantial impact. Different approaches are required for the detection and quantification of these low level leaks and are the subject of this paper. A 3 year groundwater survey was recently completed in the Surat Basin, which forms part of the Triassic-Cretaceous, Great Artesian Basin (GAB) aquifer sequence. In addition to a comprehensive water and isotopic analysis of samples from groundwater wells, gases were collected from groundwater samples and analysed for composition, '13CCO2, '13CCH4 and '2HCH4. Methane is prevalent in the major aquifers in the Surat Basin (e.g. Mooga, Gubbermunda and Hutton sandstones) and is invariably associated with a bacterial (methanogenic) carbonate reduction source, evident from its isotopic signature ('13CCH4 ~ -70', '2HCH4 ~ 220'). In addition to methane and low levels of CO2, trace levels of ethane are often detected.

Abstract: The extent to which fluids may leak from sedimentary basins to the seabed is a critical issue for assessing the potential of a basin for carbon capture and storage. The Petrel Sub-basin, located beneath central and eastern Joseph Bonaparte Gulf in tropical northern Australia, is identified as potentially suitable for the geological storage of CO2 because of its geological characteristics and proximity to offshore gas and petroleum resources. In May 2012, a multidisciplinary marine survey was undertaken to collect data in two targeted areas of the Petrel Sub-basin to facilitate an assessment of CO2 storage potential. Multibeam bathymetry and backscatter mapping (650 km2 over 5,300 line km), combined with acoustic sub-bottom profiling (650 line km) and geomorphological and sediment characterisation of the seabed was undertaken above the CO2 supercritical seal boundary of the sub-basin. Features identified in the high resolution (2 m) bathymetry data include carbonate banks, ridges, pockmark fields and fields of low amplitude hummocks located directly adjacent to banks. Unit and composite pockmarks and clusters of pockmarks are present on plains and adjacent to, and on, carbonate ridges. It is postulated that there are three possible sources for fluids and fluidised gas involved in pockmark formation: deep fluids from the basin, post-Cretaceous intra-formational, layer-bound fluids, and shallow-sourced fluidised gas from the breakdown of organic matter following the Holocene marine transgression of Joseph Bonaparte Gulf.

The Early Cretaceous Gage Sandstone and South Perth Shale formations are one of the most prospective reservoir-seal pairs in the Vlaming Sub-basin. Plays include post-breakup pinch-outs with the South Perth Shale forming a top seal. The Gage reservoir has porosities of 23-30% and permeabilities of 200-1800 mD and was deposited in palaeotopographic lows of the Valanginian breakup unconformity. This is overlain by the thick deltaic South Perth (SP) Supersequence. To characterise the reservoir-seal pair, a detailed sequence stratigraphic analysis was conducted by integrating 2D seismic interpretation, well log analysis and new biostratigraphic data. The palaeogeographic reconstructions for the Gage reservoir are based predominantly on the seismic facies mapping, whereas SP Sequence reconstructions are derived from mapping higher-order prograding sequences and establishing changes in sea level and sediment supply. The Gage reservoir forms part of a sand-rich submarine fan system and was deposited in water depths of > 400 m. It ranges from confined canyon fill to fan deposits on a basin plain. Directions of sediment supply are complex, with major sediment contributions from a northern and southern canyon adjacent to the Badaminna Fault Zone. The characteristics of the SP Supersequence differ markedly between the northern and southern parts of the sub-basin due to variations in palaeotopography and sediment supply. Palaeogeographic reconstructions reveal a series of regressions and transgressions leading to infilling of the palaeo-depression. Seven palaeogeographic reconstructions for the SP Supersequence portray a complex early post-rift depositional history in the central Vlaming Sub-basin. The developed approach could be applicable for detailed studies of other sedimentary basins

Australia has been making major progress towards early deployment of carbon capture and storage from natural gas processing and power generation sources. This paper will review, from the perspective of a government agency, the current state of various Australian initiatives and the advances in technical knowledge up until the 2010 GHGT conference. In November 2008, the Offshore Petroleum and Greenhouse Gas Storage Bill 2006 was passed by the Australian Parliament and established a legal framework to allow interested parties to explore for and evaluate storage potential in offshore sedimentary basins that lie in Australian Commonwealth waters. As a result of this Act, Australia became the first country in the world, in March 2009, to open exploration acreage for storage of greenhouse gases under a system that closely mirrors the well-established Offshore Petroleum Acreage Release. The ten offshore areas offered for geological storage assessment are significantly larger than their offshore petroleum counterparts to account for, and fully contain, the expected migration pathways of the injected GHG substances. The co-incidence of the 2009 Global Financial Crisis may have reduced the number of prospective CCS projects that were reported to be in the 'pipe-line' and the paper examines the implications of this apparent outcome. The Carbon Storage Taskforce has brought together both Australian governments technical experts to build a detailed assessment of the perceived storage potential of Australia's sedimentary basins. This evaluation has been based on existing data, both on and offshore. A pre-competitive exploration programme has also been compiled to address the identified data gaps and to acquire, with state funding, critical geological data which will be made freely available to encourage industrial participation in the search for commercial storage sites.

Geoscience Australia (GA) conducted a marine survey (GA0345/GA0346/TAN1411) of the north-eastern Browse Basin (Caswell Sub-basin) between 9 October and 9 November 2014 to acquire seabed and shallow geological information to support an assessment of the CO2 storage potential of the basin. The survey, undertaken as part of the Department of Industry and Science's National CO2 Infrastructure Plan (NCIP), aimed to identify and characterise indicators of natural hydrocarbon or fluid seepage that may indicate compromised seal integrity in the region. The survey was conducted in three legs aboard the New Zealand research vessel RV Tangaroa, and included scientists and technical staff from GA, the NZ National Institute of Water and Atmospheric Research Ltd. (NIWA) and Fugro Survey Pty Ltd. Shipboard data (survey ID GA0345) collected included multibeam sonar bathymetry and backscatter over 12 areas (A1, A2, A3, A4, A6b, A7, A8, B1, C1, C2b, F1, M1) totalling 455 km2 in water depths ranging from 90 - 430 m, and 611 km of sub-bottom profile lines. Seabed samples were collected from 48 stations and included 99 Smith-McIntyre grabs and 41 piston cores. An Autonomous Underwater Vehicle (AUV) (survey ID GA0346) collected higher-resolution multibeam sonar bathymetry and backscatter data, totalling 7.7 km2, along with 71 line km of side scan sonar, underwater camera and sub-bottom profile data. Twenty two Remotely Operated Vehicle (ROV) missions collected 31 hours of underwater video, 657 still images, eight grabs and one core. This catalogue entry refers to chlorophyll a, b, c and phaeophytin a conentrations in the upper 2 cm of seabed sediments.

Geoscience Australia (GA) conducted a marine survey (GA0345/GA0346/TAN1411) of the north-eastern Browse Basin (Caswell Sub-basin) between 9 October and 9 November 2014 to acquire seabed and shallow geological information to support an assessment of the CO2 storage potential of the basin. The survey, undertaken as part of the Department of Industry and Science's National CO2 Infrastructure Plan (NCIP), aimed to identify and characterise indicators of natural hydrocarbon or fluid seepage that may indicate compromised seal integrity in the region. The survey was conducted in three legs aboard the New Zealand research vessel RV Tangaroa, and included scientists and technical staff from GA, the NZ National Institute of Water and Atmospheric Research Ltd. (NIWA) and Fugro Survey Pty Ltd. Shipboard data (survey ID GA0345) collected included multibeam sonar bathymetry and backscatter over 12 areas (A1, A2, A3, A4, A6b, A7, A8, B1, C1, C2b, F1, M1) totalling 455 km2 in water depths ranging from 90 - 430 m, and 611 km of sub-bottom profile lines. Seabed samples were collected from 48 stations and included 99 Smith-McIntyre grabs and 41 piston cores. An Autonomous Underwater Vehicle (AUV) (survey ID GA0346) collected higher-resolution multibeam sonar bathymetry and backscatter data, totalling 7.7 km2, along with 71 line km of side scan sonar, underwater camera and sub-bottom profile data. Twenty two Remotely Operated Vehicle (ROV) missions collected 31 hours of underwater video, 657 still images, eight grabs and one core. This catalogue entry refers to porosity, total chlorin and chlorin index data from the upper 2 cm of seabed sediments.

Geoscience Australia (GA) conducted a marine survey (GA0345/GA0346/TAN1411) of the north-eastern Browse Basin (Caswell Sub-basin) between 9 October and 9 November 2014 to acquire seabed and shallow geological information to support an assessment of the CO2 storage potential of the basin. The survey, undertaken as part of the Department of Industry and Science's National CO2 Infrastructure Plan (NCIP), aimed to identify and characterise indicators of natural hydrocarbon or fluid seepage that may indicate compromised seal integrity in the region. The survey was conducted in three legs aboard the New Zealand research vessel RV Tangaroa, and included scientists and technical staff from GA, the NZ National Institute of Water and Atmospheric Research Ltd. (NIWA) and Fugro Survey Pty Ltd. Shipboard data (survey ID GA0345) collected included multibeam sonar bathymetry and backscatter over 12 areas (A1, A2, A3, A4, A6b, A7, A8, B1, C1, C2b, F1, M1) totalling 455 km2 in water depths ranging from 90 - 430 m, and 611 km of sub-bottom profile lines. Seabed samples were collected from 48 stations and included 99 Smith-McIntyre grabs and 41 piston cores. An Autonomous Underwater Vehicle (AUV) (survey ID GA0346) collected higher-resolution multibeam sonar bathymetry and backscatter data, totalling 7.7 km2, along with 71 line km of side scan sonar, underwater camera and sub-bottom profile data. Twenty two Remotely Operated Vehicle (ROV) missions collected 31 hours of underwater video, 657 still images, eight grabs and one core. This catalogue entry refers to geochemical data on piston core sediments collected during the GA0345/TAN1411 marine survey in the Browse Basin. These include concentrations of interstitial gases (C1 to C5, CO2) and high-molecular weight hydrocarbons.

The Vlaming Sub-basin Marine Survey GA-0334 was undertaken in March and April 2012 as part of the Commonwealth Government's National CO2 Infrastructure Plan (NCIP). The purpose was to acquire geophysical and biophysical data to help identify sites suitable for the long term storage of CO2 within reasonable distances of major sources of CO2 emissions. This dataset contains identifications of animals collected from 32 Van Veen grabs deployed during GA-0334. Sediment was elutriated for ~ 5 minutes over a 500um sieve. Retained sediments and animals were then preserved in 70% ethanol for later laboratory sorting and identification (see `lineage'). During sorting, all worms were separated and sent to Infaunal Data Pty Ltd (Lynda Avery) for identification to species or operational taxonomic unit (OTU). Lynda Avery completed identifications on 17 April 2013, and specimens were lodged at the Museum of Victoria. All other taxa were identified to morphospecies at GA by an ecologist. Gray shading indicates taxa identified to species level by Lynda Avery (Refer to GeoCat # 76463 for raw data of species identifications by taxonomist); all other taxa were identified to morphospecies. Data is presented here exactly as delivered by the taxonomist/ecologist, and Geoscience Australia is unable to verify the accuracy of the taxonomic identifications. Stations are named XXGRYY where XX indicates the station number, GR indicates Van Veen grabs, and YY indicates the sequence of grabs deployed (i.e. the YYth grab on the entire survey). H indicates heavy fraction animals and HS indicates animals found on a sponge. The dataset is current as of November 2014, but will be updated as taxonomic experts contribute. See GA Record 2013/09 for further details on survey methods and specimen acquisition.

Geoscience Australia (GA) conducted a marine survey (GA0345/GA0346/TAN1411) of the north-eastern Browse Basin (Caswell Sub-basin) between 9 October and 9 November 2014 to acquire seabed and shallow geological information to support an assessment of the CO2 storage potential of the basin. The survey, undertaken as part of the Department of Industry and Science's National CO2 Infrastructure Plan (NCIP), aimed to identify and characterise indicators of natural hydrocarbon or fluid seepage that may indicate compromised seal integrity in the region. The survey was conducted in three legs aboard the New Zealand research vessel RV Tangaroa, and included scientists and technical staff from GA, the NZ National Institute of Water and Atmospheric Research Ltd. (NIWA) and Fugro Survey Pty Ltd. Shipboard data (survey ID GA0345) collected included multibeam sonar bathymetry and backscatter over 12 areas (A1, A2, A3, A4, A6b, A7, A8, B1, C1, C2b, F1, M1) totalling 455 km2 in water depths ranging from 90 - 430 m, and 611 km of sub-bottom profile lines. Seabed samples were collected from 48 stations and included 99 Smith-McIntyre grabs and 41 piston cores. An Autonomous Underwater Vehicle (AUV) (survey ID GA0346) collected higher-resolution multibeam sonar bathymetry and backscatter data, totalling 7.7 km2, along with 71 line km of side scan sonar, underwater camera and sub-bottom profile data. Twenty two Remotely Operated Vehicle (ROV) missions collected 31 hours of underwater video, 657 still images, eight grabs and one core. This catalogue entry refers to high-resolution imagery taken of piston cores. A total of 20 piston cores collected in water depths between 154-445 m on the continental shelf, were imaged using the Geotek GEOSCAN IV line scan camera. Each core section was imaged at 200 lines per cm, corresponding to a 50 micron pixel size, to produce a single JPG image for each section. For more information on how the piston cores were collected please refer to the post-survey report (follow link at right), or for more information on the MSCL-S please refer to the manual, (follow link at right).