This combined SPSLCMP GPS solution has been aligned to International Terrestrial Reference Frame 2005 (ITRF2005) using the latest available International GPS Service (IGS) combined cumulative solution. Error bars are 1 sigma. All variance-covariance has been re-scaled to better reflect actual precision. Each solution circle represents a weekly combined solution. Outliers are not shown on plots. It is important to note that the length of the time series is too short for reliable vertical station velocity estimation. As the data collection and the height time series becomes longer, and the strategy of simultaneous estimation of velocities and periodical or seasonal signals is used, the estimates of the vertical crustal motion will become more accurate and reliable.

This data was compiled by ACRES Remote Sensing Science and Strategy Group. It is intended that this data be applied to the evaluation of satellite imagery geolocation and coarse resolution Digital Elevation Model evaluation. dGPS_track.txt contains yxz differential Global Positioning System tracking data. This data was collected as part of ACRES Landsat Pass Control Project, Phases 1 to 3 from 2001 to 2003. The data was filtered to remove periodic "spiking" of anomalous height values in the data Points which with a height difference of more than 5 metres between adjacent points where considered "spikes" and removed. The data present in dGPS_track.txt is considered "clean" although some "spikes" and data anomalies may still be present.

AUSGeoid98 data files contain a 2 minute grid of AUSGeoid98 data covering the Australian region, which you can use to interpolate geoid-ellipsoid separations for the positions required.You can use your own interpolation software, or you can use Geoscience Australia's Windows Interpolation software (Winter). The data files are text files in a standard format that cover the same area as standard topographic map areas. Files covering both 1:250,000 (approximately 100 x 150 km) and 1:1,000,000 (approximately 400 x 600 km) map areas are available. There is a 4 minute overlap on all sides of each area. Data format: AUSGeoid98 data files have a header record at the start of each file, to distinguish them from the superseded AUSGeoid93 data files. AUSGeoid98 data files show the geoid-ellipsoid separation to 3 decimal places, while the superseded AUSGeoid93 data files showed only 2 decimal places. AUSGeoid98 deflections of the vertical were computed from the geoid-ellipsoid separation surface, while the AUSGeoid93 deflections of the vertical were computed from OSU91A.

AUSGeoid98 data files contain a 2 minute grid of AUSGeoid98 data covering the Australian region, which you can use to interpolate geoid-ellipsoid separations for the positions required.You can use your own interpolation software, or you can use Geoscience Australia's Windows Interpolation software (Winter). The data files are text files in a standard format that cover the same area as standard topographic map areas. Files covering both 1:250,000 (approximately 100 x 150 km) and 1:1,000,000 (approximately 400 x 600 km) map areas are available. There is a 4 minute overlap on all sides of each area. Data format: AUSGeoid98 data files have a header record at the start of each file, to distinguish them from the superseded AUSGeoid93 data files. AUSGeoid98 data files show the geoid-ellipsoid separation to 3 decimal places, while the superseded AUSGeoid93 data files showed only 2 decimal places. AUSGeoid98 deflections of the vertical were computed from the geoid-ellipsoid separation surface, while the AUSGeoid93 deflections of the vertical were computed from OSU91A.

AUSGeoid98 data files contain a 2 minute grid of AUSGeoid98 data covering the Australian region, which you can use to interpolate geoid-ellipsoid separations for the positions required.You can use your own interpolation software, or you can use Geoscience Australia's Windows Interpolation software (Winter). The data files are text files in a standard format that cover the same area as standard topographic map areas. Files covering both 1:250,000 (approximately 100 x 150 km) and 1:1,000,000 (approximately 400 x 600 km) map areas are available. There is a 4 minute overlap on all sides of each area. Data format: AUSGeoid98 data files have a header record at the start of each file, to distinguish them from the superseded AUSGeoid93 data files. AUSGeoid98 data files show the geoid-ellipsoid separation to 3 decimal places, while the superseded AUSGeoid93 data files showed only 2 decimal places. AUSGeoid98 deflections of the vertical were computed from the geoid-ellipsoid separation surface, while the AUSGeoid93 deflections of the vertical were computed from OSU91A.

AUSGeoid98 data files contain a 2 minute grid of AUSGeoid98 data covering the Australian region, which you can use to interpolate geoid-ellipsoid separations for the positions required.You can use your own interpolation software, or you can use Geoscience Australia's Windows Interpolation software (Winter). The data files are text files in a standard format that cover the same area as standard topographic map areas. Files covering both 1:250,000 (approximately 100 x 150 km) and 1:1,000,000 (approximately 400 x 600 km) map areas are available. There is a 4 minute overlap on all sides of each area. Data format: AUSGeoid98 data files have a header record at the start of each file, to distinguish them from the superseded AUSGeoid93 data files. AUSGeoid98 data files show the geoid-ellipsoid separation to 3 decimal places, while the superseded AUSGeoid93 data files showed only 2 decimal places. AUSGeoid98 deflections of the vertical were computed from the geoid-ellipsoid separation surface, while the AUSGeoid93 deflections of the vertical were computed from OSU91A.

AUSGeoid98 data files contain a 2 minute grid of AUSGeoid98 data covering the Australian region, which you can use to interpolate geoid-ellipsoid separations for the positions required.You can use your own interpolation software, or you can use Geoscience Australia's Windows Interpolation software (Winter). The data files are text files in a standard format that cover the same area as standard topographic map areas. Files covering both 1:250,000 (approximately 100 x 150 km) and 1:1,000,000 (approximately 400 x 600 km) map areas are available. There is a 4 minute overlap on all sides of each area. Data format: AUSGeoid98 data files have a header record at the start of each file, to distinguish them from the superseded AUSGeoid93 data files. AUSGeoid98 data files show the geoid-ellipsoid separation to 3 decimal places, while the superseded AUSGeoid93 data files showed only 2 decimal places. AUSGeoid98 deflections of the vertical were computed from the geoid-ellipsoid separation surface, while the AUSGeoid93 deflections of the vertical were computed from OSU91A.

AUSGeoid98 data files contain a 2 minute grid of AUSGeoid98 data covering the Australian region, which you can use to interpolate geoid-ellipsoid separations for the positions required.You can use your own interpolation software, or you can use Geoscience Australia's Windows Interpolation software (Winter). The data files are text files in a standard format that cover the same area as standard topographic map areas. Files covering both 1:250,000 (approximately 100 x 150 km) and 1:1,000,000 (approximately 400 x 600 km) map areas are available. There is a 4 minute overlap on all sides of each area. Data format: AUSGeoid98 data files have a header record at the start of each file, to distinguish them from the superseded AUSGeoid93 data files. AUSGeoid98 data files show the geoid-ellipsoid separation to 3 decimal places, while the superseded AUSGeoid93 data files showed only 2 decimal places. AUSGeoid98 deflections of the vertical were computed from the geoid-ellipsoid separation surface, while the AUSGeoid93 deflections of the vertical were computed from OSU91A.

AUSGeoid98 data files contain a 2 minute grid of AUSGeoid98 data covering the Australian region, which you can use to interpolate geoid-ellipsoid separations for the positions required.You can use your own interpolation software, or you can use Geoscience Australia's Windows Interpolation software (Winter). The data files are text files in a standard format that cover the same area as standard topographic map areas. Files covering both 1:250,000 (approximately 100 x 150 km) and 1:1,000,000 (approximately 400 x 600 km) map areas are available. There is a 4 minute overlap on all sides of each area. Data format: AUSGeoid98 data files have a header record at the start of each file, to distinguish them from the superseded AUSGeoid93 data files. AUSGeoid98 data files show the geoid-ellipsoid separation to 3 decimal places, while the superseded AUSGeoid93 data files showed only 2 decimal places. AUSGeoid98 deflections of the vertical were computed from the geoid-ellipsoid separation surface, while the AUSGeoid93 deflections of the vertical were computed from OSU91A.

AUSGeoid98 data files contain a 2 minute grid of AUSGeoid98 data covering the Australian region, which you can use to interpolate geoid-ellipsoid separations for the positions required.You can use your own interpolation software, or you can use Geoscience Australia's Windows Interpolation software (Winter). The data files are text files in a standard format that cover the same area as standard topographic map areas. Files covering both 1:250,000 (approximately 100 x 150 km) and 1:1,000,000 (approximately 400 x 600 km) map areas are available. There is a 4 minute overlap on all sides of each area. Data format: AUSGeoid98 data files have a header record at the start of each file, to distinguish them from the superseded AUSGeoid93 data files. AUSGeoid98 data files show the geoid-ellipsoid separation to 3 decimal places, while the superseded AUSGeoid93 data files showed only 2 decimal places. AUSGeoid98 deflections of the vertical were computed from the geoid-ellipsoid separation surface, while the AUSGeoid93 deflections of the vertical were computed from OSU91A.