The geology and mineral prospectivity of the southern Thomson Orogen is poorly understood because the vast majority of its extent is buried beneath younger regolith and/or sedimentary rocks. To address this issue a collaborative program to drill 16 stratigraphic boreholes was proposed to collect samples of the basement geology that can be comprehensively analysed to improve the understanding of the geological evolution of this region. To reduce the uncertainty associated with intersecting the target stratigraphy at each of the borehole sites, estimates of the cover thickness were obtained by applying the geophysical techniques of refraction seismic, audio-magnetotellurics (AMT) and targeted magnetic inversion modelling (TMIM) prior to drilling.

Refraction seismic was acquired at all 16 proposed borehole sites using a system with 48 single-component geophones and a propelled weight drop primary-wave source. At 14 of the sites clear basement refractors were observed in the data. At the two other sites, Nantilla 1 and Barrygowan 1, loss of signal due to seismic attenuation at far offsets meant that a clear basement refractor was not observed. With the exception of these two sites, three distinct refractors are generally observed in the data. Those with velocities ranging from 0.4 km/s to 1.5 km/s are interpreted as regolith, those ranging from 1.8 km/s to 2.4 km/s are interpreted as Eromanga Basin sediments, and those ranging from 3.9 km/s to 5.7 km/s are interpreted as metamorphic/igneous basement. Two-dimensional velocity models of the subsurface geology were then generated using the time-term inversion method, which allowed for the thickness of each layer to be estimated. Cover thickness estimates using refraction data vary widely from site to site, with the shallowest estimate being Overshot 1 (49 m - 55 m) and the deepest Adventure Way 1 (295 m - 317 m). These variations in cover thickness estimates from site to site are indicative of basement topography variations and are not error margins.

Audio-magnetotelluric data was collected at ten sites by simultaneously deploying four porous pot electrodes, to collect the two orthogonal components of telluric data (Ex and Ey), and three magnetic induction coils, to collect the three components of magnetic data (Hx, Hy and Hz). For each dataset, a one-dimensional inversion model was produced, from which resistivity contrasts were identified and used to describe electrical conductivity discontinuities in the subsurface geology. In general, the models show a near-surface conductive layer with resistivity values ≤10 Ω·m overlying layers with continuously increasing resistivities with depth (up to 102-103 Ω·m). Those layers which were >10 Ω·m were interpreted as metamorphic/igneous basement rocks and were observed to occur at depths of ~100 m to ~300 m across the survey sites, except at Overshot 1 (38 m ±10%) and Barrygowan 1 (480 m ±10%).

Targeted magnetic inversion modelling (TMIM) was applied to freely available, good quality, regional airborne magnetic survey data. Depth to magnetic source estimates were generated for 53 targets, with confidence ratings, using a dipping tabular source body to model targeted magnetic anomalies in the vicinity of the borehole sites. A combined depth estimate was generated using a distance and confidence weighted average from multiple depth estimates at all but two borehole sites. Only a single depth estimate was available at Adventure Way 1 while no depth estimates were generated at Eulo 1. These combined depth estimates provide cover thickness estimates at the sites as they are likely sourced from, or near, the top of basement. Of the ten proposed borehole sites with coincident AMT and refraction seismic data, five sites have overlapping cover thickness estimates. Cover thickness estimates from the TMIM overlap both the AMT and refraction data at four sites and at two sites where only the refraction depth estimates were available.

2 Estimating Cover Thickness in the Southern Thomson Orogen

The cover thickness estimates presented in this report lower the risks associated with the proposed southern Thomson Orogen stratigraphic drilling program by reducing the uncertainty in intersecting the target stratigraphy at each of the borehole sites as well as allowing for better project and program planning. Successful completion of the stratigraphic drilling program in the southern Thomson Orogen will allow for each of these geophysical methods for estimating cover thickness to be benchmarked using actual cover thicknesses measured in the boreholes.